ISP1504A1
General Description
The ISP1504A1 is a Universal Serial Bus (USB) On-The-Go (OTG) transceiver that is fully compliant with Universal Serial Bus Specification Rev. 2.0, On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3 and UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.
The ISP1504A1 can transmit and receive USB data at high-speed (480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s), and provides a pin-optimized, physical layer front-end attachment to USB host, peripheral and OTG devices.
It is ideal for use in portable electronic devices, such as mobile phones, digital still cameras, digital video cameras, Personal Digital Assistants (PDAs) and digital audio players. It allows USB Application-Specific Integrated Circuits (ASICs), Programmable Logic Devices (PLDs) and any system chip set to interface with the physical layer of the USB through a 12-pin interface.
The ISP1504A1 can interface to the link with digital I/O voltages in the range of 1.65 V to 3.6 V.
The ISP1504A1 is available in TFBGA36 package.
Key Features
- Fully complies with:
- Universal Serial Bus Specification Rev. 2.0
- On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3
- UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1
- Interfaces to host, peripheral and OTG device cores; optimized for portable devices or system ASICs with built-in USB OTG device core
- Complete Hi-Speed USB physical front-end solution that supports high-speed (480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s)
- Integrated 45 ohm ± 10 % high-speed termination resistors, 1.5 kohm ± 5 % full-speed device pull-up resistor, and 15 kohm ± 5 % host termination resistors
- Integrated parallel-to-serial and serial-to-parallel converters to transmit and receive
- USB clock and data recovery to receive USB data up to ±500 ppm
- USB data synchronization from 60 MHz input to 480 MHz output during transmit
- Insertion of stuff bits during transmit and discarding of stuff bits during receive
- Non-Return-to-Zero Inverted (NRZI) encoding and decoding
- Supports bus reset, suspend, resume and high-speed detection handshake (chirp)
- Complete USB OTG physical front-end that supports Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
- Supports external charge pump or 5 V VBUS switch
- Complete control over bus resistors
- Data line and VBUS pulsing session request methods
- Integrated VBUS voltage comparators
- Integrated cable (ID) detector
- Highly optimized ULPI-compliant interface
- 60 MHz, 8-bit interface between the core and the transceiver
- Supports 60 MHz output clock configuration
- Integrated Phase-Locked Loop (PLL) supporting input clock frequency of 19.2 MHz
- Fully programmable ULPI-compliant register set
- Internal Power-on Reset (PoR) circuit
- Flexible system integration and very low current consumption, optimized for portable devices
- Power-supply input range is 3.0 V to 4.5 V
- Internal voltage regulator supplies 3.3 V and 1.8 V
- Supports external VBUS charge pump or 5 V supply: External VBUS source is controlled using the PSW_N pin; open-drain PSW_N allows per-port or ganged power control
Digital FAULT input to monitor the external VBUS supply status - Pin CS_N/PWRDN 3-states the ULPI interface, allowing bus reuse for other applications
- Supports power-down mode when VCC(I/O) is not present or when pin CS_N/PWRDN is HIGH
- Supports wide range interfacing I/O voltage of 1.65 V to 3.6 V; separate I/O voltage pins minimize crosstalk
- Typical operating current of 10 mA to 48 mA, depending on the USB speed and bus utilization
- Typical suspend current of 50 µA
- Typical power-down current of 0.5 µA
- Full industrial grade operating temperature range from –40 °C to +85 °C
- ElectroStatic Discharge (ESD) compliance
- JESD22-A114D ±2 kV contact Human Body Model (HBM)
- JESD22-A115-A ±200 V Machine Model (MM)
- JESD22-C101-C ±500 V Charge Device Model (CDM)
- Available in a small TFBGA36 (3.5 mm x 3.5 mm) Restriction of Hazardous Substances (RoHS) compliant, halogen-free and lead-free package
Applications
- Digital still camera
-
Digital TV
-
Digital versatile disc (DVD) recorder
- External storage device, for example:
- Magneto-optical (MO) drive
- Optical drive: CD-ROM, CD-RW, CD-DVD
- Zip drive
- Mobile phone
- MP3 player
- PDA
- Printer
- Scanner
- Set-top box (STB)
- Video camera
CONTACT
For USB technical support and errata sheets (if any), contact wired.support@stericsson.com
Supporting Documents
| Type: | Description: | File Size: | Download: |
| Application Note | Interfacing to the ISP1504, ISP1505 and ISP1506 | 335KB | download |
| Brochure | USB transceivers | 236KB | download |
| Brochure | USB OTG. A tutorial on USB On-The Go | 354KB | download |
| Brochure | Ultra-low-power transceiver solutions | 886KB | download |
| Datasheet | ISP1504A1; ISP1504C1 ULPI Hi-Speed USB On-The-Go transceiver | 1976KB | download |
| User Manual | ISP1504A1; ISP1504C1 ULPI transceiver eval board | 281KB | download |
